Visual Fault Locator

1.Constant power output

2.Laser head anti-drop design

3.Laser case ground design prevents ESD   damage

4.Portable and rugged

5.Easy to use

Optical light source

1.Providing 1~4 wavelengths output and   wavelengths can be optional

2.CW, 2Hz modulation output at 650nm, and   CW, 270Hz,1KHz,2KHz

3.modulation output at other wavelengths.

4.High stability of the output power

5.Stable output wavelength

6.Compact size and decent appearance

7.Large LCD, easy operation

Optical Fiber Identifier

1.Novel and beautiful appearance and   structure design;

2.Indicate the signal directions and power   in fiber

3.Indicate the signal presence or absence   (Live or dark fiber)

4.Efficiently identifies the traffic   direction and frequency tone (270Hz, 1KHz, 2KHz) with audible warning

5.Displays the relative core power

6.Don't need to replace adaptor

7.Lower power indication

8.Build in VFL function

Optical variable attenuator

1.Stepwise attenuating by circumgyrated   dial: attenuating step 0.05dB

2.Provide with the function of displaying   dB and dBm attenuating value

3.10 minutes Auto-off function can be   activated and deactivate with keypad operation.

4.After off the instruments, the system   will have the memorizing of the attenuating value and the attenuating step,   in order to restore the system back to the previous shut down state when open   the instruments next time

5.Portable, rugged, lightweight; Easy to   use.

Optical Power Meter 

1.Large-screen display clearly

2.Wave ID—Auto wavelength identification   & switching

3.Frequency ID ---Auto frequency   identification

4.Intelligent backlight

5.Reference power level can be set up and   stored

6.User self-calibrating function

7.Auto-off function

8.Up to 200hrs battery life

9.Support alkaline battery, Ni-MH   rechargeable battery power supply  

PON Optical Power Meter

1.It can experiment at Voice, data and   video signal synchronous measurement and display on BPON/EPON/GPON.

2.*Providing simultaneous measurement for   all three wavelengths on the fiber (1490nm, 1550nm,1310nm).

3.Used in Burst mode measurement of 1310nm   upstream.

4.Optional Chinese/English display.

5.Offers up to 10 different threshold sets   in total, three status LEDs represent different optical signal conditions of   Pass, Warn and Fail respectively.

6.Good key design, high sensitivity,   greatly reducing the volume and weight of the tester.

7.Different models corresponding to   different function, according to own use to choose.

OTDR

1.VFL (visual fault locator，as standard function)

2.The VFL, available as a standard module   in SPTK-3302F series OTDR, offers built-in 650nm visual fault location

 on a FC/UPC connector.

3.PM (power meter，as standard function)

4.SPTK-3302F series OTDR comes with   optional built-in power meter that let technicians easily verify the

 presence of a signal.

5.LS (laser source，as optional function)

6.SPTK-3302F series OTDR comes with   optional built-in laser source through OTDR1 Port that let technicians 

easily verify the total loss of the   local network with a power meter.

7.FM (fiber microscope，as optional function)

8.The optional fiber inspection probe   facilitates the inspection before the connection. SPTK-3302F series   OTDR 

offers this capability through a USB   port connection, which allows quick and easy inspection of connector end   faces for contamination and also enables it capture and store the image.

9.PON Online Test (as optional function)

10.SPTK-3302F series OTDR uses 1625nm   wavelength to scan and analyze the access point and proceed online 

testing with optical filter, and will   not disturb the service.

OTDR Launch Cable Box

1.Pulse Suppressor, Launch Box, Delay   Line, Installation/Testing, Training, Calibration

2.Compound Latch for positive seal and   easy opening with locking feature

3.Water and dust prove allowing the unit   to be taken into almost any environment

4.Auto Purge Valve for changes in altitude   and temperature